The device is Becker Ready 50 bdc02 ec101.
I was trying to unlock the device,and put some files in the internal memory.Now it shows only the red logo and stays there.I don't have access to the internal memory.Windows says - mass storage device and after 20 seconds it gets code10. It can't boot from sdcard.I've tryed with sd and sdhc class4 ,FAT and Fat32 with no success. Is there something i can do, or the device is dead. Thanks in advance.

I have same problem with Becker Ready 45,anny ideas?

:bs_quesexclaim::bs_quesexclaim:

nikirumenov wrote:The device is Becker Ready 50 bdc02 ec101.
I was trying to unlock the device,and put some files in the internal memory.Now it shows only the red logo and stays there.I don't have access to the internal memory.Windows says - mass storage device and after 20 seconds it gets code10. It can't boot from sdcard.I've tryed with sd and sdhc class4 ,FAT and Fat32 with no success. Is there something i can do, or the device is dead. Thanks in advance.

What did you do EXACTLY ?
And what is on SD (don't matter what class)

sasans wrote:I have same problem with Becker Ready 45,anny ideas?

Really?
EXACTLY the same files you put in the internal memory? What files? What location in memory?





Without proper information, we are stuck to what we read. We have no crystal ball

Sorry,i used this [Please Register or Login to download file] tutorial to put Igo Primo and when i reboot it stuck at logo. Sorry for bad english.

I use tutorial Becker 45/50 update and unlocking and copy files:iboot.exe,iboot.mscr,MortScript.exe and folder MoblileNavigator to root. Then in folder MoblileNavigator i put IgoPrimo and rename primo.exe to MobileNavigator.exe.When i restart device it stop at becker logo. When i conect Becker to computer nothing happens i hear the sound but windows not recognize the device. Sorry for my bad english.

Did you not make any spelling errors? The name should be MobileNavigator, not MoblileNavigator (as you write and as spelled on the site you linked to). The correct spelling is very important in the path, if spelled wrongly, Primo will not be found.

I wrote MoblileNavigator. What can I do? I have original backup but pc does not see the device.

Same problem. Any program or something?
How can i make hard reset to device

Tried to put iGo to Micro SD. Nothing works

[device]
type="BECKER_2010Q3E1"

[utility]
calibratefix=1 ; ; If gps signal don't lost write - "0"; if lost write "1"

[Interface]
resolution_dir="480_272"
vga=0
show_exit=1
show_minimize=1
extra_settings=1
shutdown_time=0
capture_to_jpeg=1
show_mapchanger=1
show_programs=1
shutdown_time=0


[rawdisplay]
highres=0
screen_x=480
screen_y=272
class="landscape"

[folders]
app="%SDCARD%/iGo8""

[gps]
baud=57600 ;- write "baud rate"
port=5 ;- write port
source="virtserial"
set_messages="0" ;

[mapchanger]
map_ta="TELEATLAS" ; - you can write other title
map_nt="NAVTEQ"
map_ot="TOP MAP"

[tripcomputer]
num_of_trips=4

[vr]
disabled=0

[3d_config]
disable_roadsign_navigation_mode=0
roadsign_lines_per_screen=10
rotated_roadsigns=0

[sound]
csv_voice_enabled=1
ding=0

[debug]
skip_eula=1
screenshotsavecameraini=0
screenshotfilename="\captures\ecran_%02d.jpg"
show_battery_percent=1
experimental_features=1
show_networkservices=1

[lua]
backlightdetails=1

[gestures]
border_width=130

[network]
available="1"

[tmc-http]
enabled=1

[http]
enabled=1

[other]
demo_enabled=0

[map]
show_oneway=1
2dheadup=1
show_oneway_3d=1
poi_grouping_distance=0
3d_max_zoomlevel=800;
3d_min_zoomlevel=30;40
speedcam_visibility=500;
3d_max_tiltlevel="8700"
3d_default_tiltlevel="8200"
3d_max_zfar=5000
3d_buildings=1
3d_landmarks="1"
3d_roads="1"
3d_tunnels="1"
follow_gps=1

[2d]
guidancearrow_disappearlevel=600
guidancearrow_maxshift=12
minguidancearrowsize=20
minguidancearrowsize_zoomlevel=1200
maxguidancearrowsize=65
maxguidancearrowsize_zoomlevel=0

[3d]
planned_route_track_width="5"
planned_route_track_contour_width="1"
planned_route_contour_width="1"
max_pois_on_horizont="5"

[navigation]
junction_view_distance=300 ;(200)
junction_view_distance_ramp=300 ;(400)
junction_view_distance_highway=400 ;(800)
simple_crossborder_warning=1
use_duration_for_tunnel=0
show_current_city=1
show_city_in_next_street = 1
show_city_in_next_street_distance = 1000
autoreplan_action="AUTO"
gps_pos_to_road=1
show_countrychange=1

[camera.roundabout]
enabled=0

[feature]
text_guidance=1
signpost_coloring=1
tmc_event_coloring=1
tmc_traffic_side=1
ding=0

[dynamiccompressor] ;TTS voice
compressor=1
gain=10

[tts]
automatic_direction_conversion=1
announce_exit_directions=1
always_say_road_names=3
skip_exit_numbers=1

[warning]
speedcam_enabled=1
speedcam_warning=1
speedcam_max_lookahead=1000
speedcam_maxdistance_from_road=50

[Debug]
skip_eula = 1
experimental_features = 1;

Hi,
Did you solved your problem with becker, how???
Please tell me, i have same problem with my becker.
Thanks.

No,i send my device to expert. Now waiting for his answer.

Same Problem happened to me. Becker Transit 45 (BE S11).
Can somebody help me???

-> I put the files from http://www.navitotal.com/post136044.html?hilit=unlock%20transit#p136044 into the root(device) (with the original files)

If I trying to do a "Hardreset" (>7sec ON/OFF Button) -> it boots to the red "Becker" Screen and nothing happens

I have same problem with Becker ready.6,anny ideas? Thanks

I have a same problem with ready 45. Is there any solution? My comp not recognized becker,only usb mass storage. Please help