Primo 2.4 - how to zoom in more on map screen   

Primo 2.4 - how to zoom in more on map screen

Postby surreychris » Thu Feb 28, 2013 12:47 pm

Hi all
I have just upgraded my double din 128mb chinese system from igo8.3 to primo 2.4 and am trying it to see if i like it.

On my igo8 i was able to zoom the map in so the streets were larger to see and the 3d car was bigger but i cant seem to do this on the primo.

when i tap the screen to bring up the arrow buttons the '+' zoom in button is greyed out and only the '-' zoom out button is workable which makes the map even further out and the streets smaller.

Ive tried this in both the default skin and the dimka screen.

Is this not possible, id rather see a smaller area and bigger streets etc

thanks

Chris
surreychris offline


Junior Member



 
Joined: Sun Dec 04, 2011 2:36 pm
Posts: 10
Has thanked: 0 time
Been thanked: 0 time

Postby furat52 » Thu Feb 28, 2013 8:25 pm

go to settings\map settings and change the viewpoint to normal, high or low as desired.
furat52 offline


Junior Member



 
Joined: Mon Oct 24, 2011 4:19 pm
Posts: 93
Has thanked: 1 time
Been thanked: 6 times

Postby surreychris » Thu Feb 28, 2013 9:19 pm

ive done that, i have it set to low but its still not very large
Igo8 goes much larger
surreychris offline


Junior Member



 
Joined: Sun Dec 04, 2011 2:36 pm
Posts: 10
Has thanked: 0 time
Been thanked: 0 time

Postby furat52 » Fri Mar 01, 2013 10:48 am

if you are using Dimka skin then go to settings\mapsettings tab to enable user zoom settings, then tab user zoom settings and I suggest to do the follwoing (if you dont want the sky to be appeard in the map):

minimum angle 55
maximun angle 72
maximum angle with signposts 78

then in the speed settings select and enable the speed zoom and select the minium speed =1km/h and maximum speed =100km/h

the above are my settings, ofcource you can alter the values for what ever you want.
furat52 offline


Junior Member



 
Joined: Mon Oct 24, 2011 4:19 pm
Posts: 93
Has thanked: 1 time
Been thanked: 6 times

Postby surreychris » Fri Mar 01, 2013 11:19 pm

Hi
I've tried different settings but none make the map zoom in close enough.

It adjusts the angle showing the sky or not but not bringing the area shown smaller.

The screen shows about 20 to 30 square miles instead of prob 5 to 10 that I'd like.

The zoom out button works fine and when I zoom out the zoom in button appears but dissapears when I get back to this level.

As I said, this can be done on 8.3 but I can't find a way with primo 2.4

Thanks for the suggestions
surreychris offline


Junior Member



 
Joined: Sun Dec 04, 2011 2:36 pm
Posts: 10
Has thanked: 0 time
Been thanked: 0 time

Postby surreychris » Mon Mar 04, 2013 10:50 am

anyone got any more ideas ??
surreychris offline


Junior Member



 
Joined: Sun Dec 04, 2011 2:36 pm
Posts: 10
Has thanked: 0 time
Been thanked: 0 time

Postby crb247 » Sun Mar 10, 2013 4:29 am

If you are using a sys.txt file try removing it (or what i do is temporarily rename it to testing.txt) and reboot the unit letting the default primo 2.4 settings to kick in. I had a few settings in the sys.txt for primo2 that did not seem to like primo 2.4.
crb247 offline


User avatar Junior Member



 
Joined: Tue May 22, 2012 1:41 am
Posts: 20
Location: Northen Ontario, CA.
Has thanked: 1 time
Been thanked: 3 times

Postby surreychris » Tue Mar 12, 2013 8:06 pm

Hi
Tried this by renaming the sys file sysold and made no difference.

I didnt think it would because nothing in the sys file mentions anything about scale with or without min and max values that i maybe could change.

Maybe Primo 2.4 cant zoom in on the map to as small a scale that igo8 can tho I do find that hard to believe
surreychris offline


Junior Member



 
Joined: Sun Dec 04, 2011 2:36 pm
Posts: 10
Has thanked: 0 time
Been thanked: 0 time

Postby kadukovci777 » Tue Oct 15, 2013 7:51 am

Hi.
i had same issue on my htc one android phone.i used before primo 2.01,all been great shows very large.but after installed primo 2.4 zoom was very small.i replaced sys txt file from iGO root directory.i am using sys txt from primo 2.01.all fine now.maybe you could try same way,maybe will help you.
kadukovci777 offline


Junior Member



 
Joined: Sat Dec 18, 2010 11:33 pm
Posts: 1
Has thanked: 1 time
Been thanked: 0 time


Return to General Discussions about iGO core

 


  • Related topics
    Replies
    Views
    Last post

Who is online

Users browsing this forum: No registered users and 49 guests