Hey.
I have the following problem but igo wal. I got home igo wal from the network and follow the installation wizard and get the program started. But then when I'm going to put maps so it would not start up the program again. I then get an error message. hope someone can help me with this problem.

Here is the error message.

------------------------------------------------------
------------------------------------------------------
------------------ Crash Log Begin -------------------


Current System time: "2014-07-03 20:27:18"
Build version: 9.6.13.267029
Build configuration: Product--ARCHFAM
OS version: 6.0

Uptime: 0 h 0 m 8 sec 0 msec

Memory Stats:

FreeMemory: 51 MB, 808 KB, 0 B
TotalUseableMemory: 60 MB, 96 KB, 0 B
MaxMemory: 129 MB, 0 KB, 0 B
ReservedMemory: 1 MB, 0 KB, 0 B
ActualCacheSize: 4 MB, 445 KB, 80 B
GarbageSize: 4 MB, 445 KB, 80 B


Exception: 0xc0000005
At address: 0x00039a08
Access violation reading address: 0x0001022c
0x00039a08 (A)


WinCE CallStack snapshot (function names unknown - map file \StorageCard\Primo2.map not found):

0x40029688 (A)
0x008ccd14 (A)
0x008cc2ec (A)
0x008cc49c (A)
0x008cc584 (A)
0x0028c638 (A)
0x4007726c (A)
0x40058418 (A)
0x400525e8 (A)
0x4002a91c (A)
0x4002ac0c (A)
0x400526e8 (A)
0x00039a08 (A)
0x0003adec (A)
0x0002c338 (A)
0x0002d2fc (A)
0x001df304 (A)
0x00127acc (A)
0x001e37c8 (A)
0x001e120c (A)
0x001e5a04 (A)
0x00429350 (A)
0x000611d4 (A)
0x00061380 (A)
0x008f6d14 (A)
0x0005ece8 (A)
0x00429350 (A)
0x0009d048 (A)
0x0009d0c0 (A)
0x0005ca8c (A)
0x0005c794 (A)
0x0005efb8 (A)
0x0005ffe8 (A)
0x0028c3d8 (A)
0x0028c5ec (A)
0x0009cd18 (A)


Global status:

bInFocus: 1
bMouseDown: 0
bInLogic: 0
bInRender: 0
CurrentState[128]:
GPS Pos: (0.000000,0.000000)
Camera: pos:(0.000000,0.000000) rot:0 persp:0 zoom:0.000000 eng=0)


Maps:



------------------- Crash Log End --------------------
------------------------------------------------------
------------------------------------------------------

mistype primo should be. =)
my device I use is a stereo from ebay erisin 1065d.
program I got home called iGo Primo 2.4-96.13 Complete
and the maps are the same as those that were recommended by the program.

Are the maps (with the extension .fbl) in the folder content/map (not maps)?

I have the exact same issue.Although my primo works, but crashes on exit and activating the included POI.

Yes. there is in the content/map, I will try to load older map from 2012 tomorrow and see if that will work. But i'dont think so.

TobbeIgo wrote:I then get an error message.

Can you post here the exact message you get? (not the crash log).

DariusIII wrote:Although my primo works, but crashes on exit

Take a look here.

Thank you, will test it to see if that solution works.

Most errors can be solved with a clean build of igo

I will try to install the program again and then load another map package and see if that will work. I don't get any wrong massage the gps turn it off then restart and this crash log is all i get.

So, now I got it work with the map, though, so I added just to the Swedish map, but will try to add all over europe. However as I tried to have with me two sd card with me the one where I had not added maps but only tts voice and with the sd card in so crashed the system. think I located the problem to this file, it is worth spending time to get tts to work? 'll try to add regular Swedish voice only.
just want to add that I added maps from a map, however, older package but will try to add the newer maps now,

Have you followed the tutorial to get tts going?