I have a TomTom One (v2) with a 4GB SD card.
I have put NavCore NC9.510_DSA_For 32Mb_ram on it.
I installed the map Benelux_1030_9519 on it.
And then it's working fine.
But when i install the map Western_Europe_1030_9519 on the SD card.
The TomTom is constantly freezing and rebooting.
When I remove Western_Europe_1030_9519 map the TomTom is working fine again.

Any one any suggestion how to solve this?

robjanssen wrote:I have a TomTom One (v2) with a 4GB SD card.
I have put NavCore NC9.510_DSA_For 32Mb_ram on it.
I installed the map Benelux_1030_9519 on it.
And then it's working fine.
But when i install the map Western_Europe_1030_9525 on the SD card.
The TomTom is constantly freezing and rebooting.
When I remove Western_Europe_1030_9525 map the TomTom is working fine again.

Any one any suggestion how to solve this?

use
[Please Register or Login to download file]

I made a typo.
I'm trying to use Western_Europe_1030_9519
Does that make any difference?
But also did try Western_Europe_1030_9525.
And then also freezes and reboots.

Now downloading NavCore v9.541 SE_GL_1-Time_ok_one_xl

@holyhead with NavCore v9.541 SE_GL_1-Time_ok_one_xl the device is still freezing/rebooting.
Any other suggestions?

Are you using the map without speedcams ?

And what happens if your first choose the Benelux and if that
is alright you changed over to the west Europe map.
I have just done that with Europe and it works fine on my One New Edition (V2).

I'm using the map with speedcams.
Can that cause the problem?
Will try without speedcams!

robjanssen wrote:I'm using the map with speedcams.
Can that cause the problem?
Will try without speedcams!

Depends on the speedcams your use. It is worth to try it without the speedcams.

Without the speedcams the map Western_Europe_1030_9519 is working.
But will that mean I cannot use speedcams?
I tried the map Benelux_1030_9519 with speedcams.
And that one is working fine with speedcams.
So why is Western_Europe_1030_9519 not working fine with speedcams?
Or can it be the problem that I copied all the speedcam files to the map Western_Europe_1030_9519?
For Benelux I only copied the NL, BE en LU files.

robjanssen wrote:Without the speedcams the map Western_Europe_1030_9519 is working.
But will that mean I cannot use speedcams?
I tried the map Benelux_1030_9519 with speedcams.
And that one is working fine with speedcams.
So why is Western_Europe_1030_9519 not working fine with speedcams?
Or can it be the problem that I copied all the speedcam files to the map Western_Europe_1030_9519?
For Benelux I only copied the NL, BE en LU files.

The problem is that you copied all speedcams to the map. Only copy the speedcams van Western_Europe.

Thank you. I will try that.
Can I copy both "normal" and Premium speedcams?
Or do they not work together?

robjanssen wrote:Thank you. I will try that.
Can I copy both "normal" and Premium speedcams?
Or do they not work together?

Premium is enough

SpeedCams Premium:   Normal Speedcam + extra
                     route controls
                     railway crossings
                     locations where many accidents occur
                     locations with obvious mobile flash units

SpeedCams Normal : vaste flitsers
flitsers voor rood licht
flitsers bij toeritdosering
flitsers in beide richtingen


SpeedCams Premium: vaste flitsers
flitsers voor rood licht
flitsers bij toeritdosering
flitsers in beide richtingen

+ extra

trajectcontroles
spoorwegovergangen
locaties waar veel ongelukken voorkomen
locaties met voor de hand liggende mobiele flitsers

I only copied the speedcams of Western Europe.
And now it's working.

But I have another (small) problem.
Every time after turning the device off. When I turn the device on back again. I have to choose the map Benelux or Western Europe. And also the time has been reset to 0:00.
Is this is a setting?
With Navcore NC9.510_DSA_For 32Mb_ram the map and time were not lost after a reboot/restart.

Open with notepad the file setconfig.txt
delete the line delmap
close the file and that should solved the problem with the map.
That the time goes,s to 00.00 is normal with this navcore. After a GPS fix the time should be alright.

If the Navcore NC9.510_DSA_For 32Mb_ram was working alright you can alway,s go back to that navcore.

Removed the delmap option. And that one is working fine now.
Thank you.

Another problem.
After turning off the device, it powers on again automatically after a second of 10.
Any ideas?

robjanssen wrote:Removed the delmap option. And that one is working fine now.
Thank you.

Another problem.
After turning off the device, it powers on again automatically after a second of 10.
Any ideas?

I have no idea. I have tried my TomTom new edition (V2) with exactly the same navcore. Maps Benelux and western_Europe with speedcam and the one is not power on after 10 seconds.
Hopefully someone has the solution for it or otherwise go back to your 9510