News of General Discussions about iGO core - Page 162

Sorry Chas521

If you pick this up yes I am back.

Normally get my speedcams from scdb and they come in a single file which gives my a single icon for all categories. Most sites seem to do the same for Igo but (yes I will wash mouth out) Tomtom seem to get them categorised into speeds. Also does Igo accept multiple speed txt files (Yes I could try and see what happens )

Sent ...

Can somebody help me please, i set up the truck settings (height width and so on) but i still get routed through low bridges. Any help would be great thanks :confused:

Hi everyone am hoping that someone will help an old senile codger (was going to say git :o

Using

Igo Primo 8.5.11.155811
Teleatlas UK 2010.06 maps in Content-Map
Teleatlas UK 2010.06 poi in content-poi
My download poi in content-userdata-poi (have kix,kml,kns & kst files )
My download bmp in content-userdata-usericon

kmlpoi in data.zip deleted

sys.txt includes


kmlpoi="storage card\primo\content\userdata\poi"
kmlicon="storage card\primo\content\userdata\usericon"
poi="storage card\primo\content\userdata\poi"


multipoi=1
use_multi_poi_icon=1
sort_by_config=1
inherit_visibility=1
default_visibility_altitude=10000
userpoi_has_mypoi=1
enable_pois_before_080217=1
max_quicksearch=”yes”
deviation_divident=4
detour_interval_1=300
detour_interval_2=1000 ...

hi carnt seem to find the maps for uk only can someone point me in right direction ty

Hi all,

I've heard about this new NAV which is for off-road navigation.
Is it available for download/use? which maps does it requires?
which PNA/PDA can run it?
Can anyone plese ellaborate?

Thanks,
Danny

Hey everyone... is there any way to make Igo Primo always go into stand by mode once the external power (i.e. car adapter) is disconnected? Sometimes my PNA with Primo goes into standby mode properly, but then sometimes it says "running on battery."

Besides guaranteeing my PNA with primo go into standby mode (sleep mode), is there any way to prevent my gps/pna for turning on again for at least 20 seconds? Kinda like a ...

Hi,

A few days ago Penavis posted a thread regarding 3d buildings for Europe
(http://www.navitotal.com/forums/showthread.php?3575-Mio-Mireo-Buildings-3D-mostly-Europe).

A small question: In IGO building files have the 3dl or (3dc for Primo) extention, while the files
in this thread have a cpf extention.
These will probably be a mismatch - should the extention be changed?
Is there any daptation required before usage?

Thanks,
Danny

Hi,

I'm trying to help a friend installing Primo on his MioMoov 300 unit.
I've installed it into the internal flash and it works great. The problem is
that the internal flash is limited and only small content volume
can be used (i.e. 2-3 maps).

So the solution is to use an external SD card that will store the content folder
and instruct the Primo to use that content (Chas521 and/or Nabi explained
how to ...

Hi

I'm new here looking for some info please. I have a Mio C710 2006 vintage and cannot get updated maps - apparently Mio do not support these units any longer. I believe ig0 can be used, how do i get this and how do i load it to my unit ?

any help appreciated

corkbuoy

Hi Bro Chas, I am not really suggest but wonder where to made request if I got no idea at all what software to use? I am from Malaysia and familiar with Papago is working fine in Malaysia. But recently my relative plan to have a vacation in Australia. So Is there any link where to put enquiry what software is working fine in What Country? I heard that Igo is Good In Europe (Do ...