I've being reading, testing and trying without luck.

All the files are downloaded from this site

I installed iGO on my advent OE OTORAV1 for a Toyota RAV4, I used iGo-Primo 2.4 9.6.13 Complete from Y.T. and also tried chas521 and mikyhouse55. the gps works as expected, i receive no errors or any problem EXCEPT no sound or voice guidance. i installed the TTS files and/or TTS PRO files and i am getting no sound ...

Hi

I have a bit of a problem on my Chinese double din where IGO Primo v2.0 will just suddenly cause my device to reboot for no apparent reason. I could be just driving along following the prescribed route and then bam it just reboots, sometimes I get an out of memory error but normally it just suddenly reboots.

I think this has to do with the device running out of memory, this is my ...

Hello,

I just installed Primo 2.4 on a GPS running winCE 6.0 (most likely a chinese one, branded Klipad GPS4328). It runs OK but I noticed the brightness slider from inside the app doesn't do anything (no dimming of the backlight).

I googled a bit and found a couple of topics about the backlight not working, tried pretty much all the solutions proposed in the threads I found but still no luck... The best I ...

I found this site a few days ago while looking for maps for my valor ddn-868W. I found this thread:

http://www.navitotal.com/showthread.php?9094-Valor-ddn-868w-with-gogo-maps-from-engistech

I downloaded the IGO8 core (and extracted via WINRAR) that chas521 posted from his march 2011 thread referenced in the above thread. I edited the sys.txt file with the suggestions that he made for my screen resolution 800X480, and from post #15 in this thread:

http://www.navitotal.com/showthread.php?7708-Help!-Installing-iGO-8.3-Picture-goes-all-white-and-rolls!/page2&highlight=chas521

I am in the US, so I downloaded ...

Hello everybody
i am new at this forum so please forgive me i post at the wrong forum
i have bought this car multimedia system from dealextreem and i have difficulties to install i go 8 in it.

i have tried several times to install i go 8 and no one worked
please if some one have an idea how to do it please contact me
i am getting desperate
i don't know what i ...

i have just got a igo8 with wince6 and i was wondering if i can put navteq maps on it
its running 8,3,4,14 7"screen says it was built may 11/2010
any help or point me in right direction
many thanks

Hi guys
I still have an on-going problem with Primo 2.4 I have a Chinese 800x480 unit and my preferred cockpit layout is the alternate 2. When I select it from the menu, it restarts and I get the following error message. Failed to open file ui_igo9\800_480\ui\\cockpit2.css exiting application. On investigation in the data file I have found that the file requested is missing. I messed around trying to use data files from previous versions ...

Hi all,

I am running Primo 2.4 & have troubles with loading schemes/skins.
When I go into setup/map display & change day or night colours I gat the error - Cannot find 'ui_igo8/common/trackinglist.spr'

What is causing this?
How do I correct?
What setting do I need?

I have the standard '.zip' files in content/schemes etc.

Thanks

Yesterday, while driving and I was very close to my destination in an industrial zone, I got a popup saying "This route requires a special permit" or something similar which I cannot recall. The popup window had an OK button below the message, but when I clicked on it nothing happened. So, with this popup blocking the screen, the GPS was practically not functional. I do not know what would have happened if I had ...

Hi

I seem to be getting an intermittent issue where occasionally IGO Primo 2.0 looses the GPS signal for no apparent reason. Sometimes it comes back quite quickly and sometimes it doesn't even after a reboot. It is NOT an issue with satellite visibility as there is nothing blocking the receiver on the dash and it is clear blue sky.

Any ideas welcome, I know some have some settings in their sys.txt file but as ...