PAPAGO! R6100 - X7 Reality M3GPS (Sept 2010 Edition) + Suppo

To Monters GPS,

Can you send me the uncompress happy file.

Thanks.

PM me the link Please

"Regarding the reg code, if wrong code, the map will shift and will not show you in right location. First put in 0000000000 and check the location. The gps coordinate in system status shows the actual figure. Compare with the coordinate from trip computer. If the code correct, both coordinates are the same, means no shift.

What is this "trip computer" ?


Thanks

Paleskin wrote:What is this "trip computer" ?


Thanks

It is "travel computer", you can see it after pressing button Navi>mode>travel computer
You will see coordinate of your position...by checking coordinate you can compare your actual position and yr car coordinate, but this way quite difficult to be done, it will be easier if you can check position (not the coordinate) of yr actual and car position that indicated in yr gps.

Nagas wrote:It is "travel computer", you can see it after pressing button Navi>mode>travel computer
You will see coordinate of your position...by checking coordinate you can compare your actual position and yr car coordinate, but this way quite difficult to be done, it will be easier if you can check position (not the coordinate) of yr actual and car position that indicated in yr gps.

So I need to compared the coordinates from ------> advance setting ------> system status (the right one) with the coordinates from -----> Navi>mode>travel computer (the wrong one) and adjusting the wrong one to be the same as the right one using reg code ?

Paleskin wrote:So I need to compared the coordinates from ------> advance setting ------> system status (the right one) with the coordinates from -----> Navi>mode>travel computer (the wrong one) and adjusting the wrong one to be the same as the right one using reg code ?

How To :
1. Start program from X7 with OpenReg.exe------> Use COM as your GPS COM Port.
2. Key In Reg Code---> Trial and error to find correct position. I got correct result 0799000000.
3. After got correct position...next time run program using X7_C..... (without Open Reg and use suitable COM as your gps).

"Regarding the reg code, if wrong code, the map will shift and will not show you in right location. First put in 0000000000 and check the location. The gps coordinate in system status shows the actual figure. Compare with the coordinate from trip computer. If the code correct, both coordinates are the same, means no shift.

If there are shift, observe whether N coordinate or E coordinate different. Normally, the E coordinates are the same, only the N shifted. Then you have to key in the combination to check. The first 5 digits shifts the N coordinates and the other 5 digits shift the E coordinates. You have to key in 1 combination, compare coordinates, if not ok, exit and restart again with a different. You have to write it down each time the different numbers and the effect on the coordinates.

Tips, the reg number is related to the memory card id. Initially my number is 0998000000. But when I copy into another memory card, it shifted and try again and got 0996000000 to work perfectly.

A lot of hard work, but believe me, once you got it, it will sure make your day."

FYI, my sweet number is 0798000000. I think torsten no is 0799000000. I am in Malaysia, Torsten is not. So I think location have no impact.

Tips:
Make sure you stay stationary at 1 location, and write down. Don't be lazy because you need to analyze the result to find out which number to change and to tembak more accurately.

Try not to do this at night for 2 reasons:
1) Dengue fever is on the rise and you are the sitting duck for mosquitoes.

2) At night is quiet. Your neighbours will be wondering what the heck are you doing after hearing "...Papago music...Searching for satellite...satellite search complete... " repeat and repeat for 15 minutes or more. (I did at night, mute sound .and close car door, sweating all over)

Monters GPS wrote:How To :
1. Start program from X7 with OpenReg.exe------> Use COM as your GPS COM Port.
2. Key In Reg Code---> Trial and error to find correct position. I got correct result 0799000000.
3. After got correct position...next time run program using X7_C..... (without Open Reg and use suitable COM as your gps).

"Regarding the reg code, if wrong code, the map will shift and will not show you in right location. First put in 0000000000 and check the location. The gps coordinate in system status shows the actual figure. Compare with the coordinate from trip computer. If the code correct, both coordinates are the same, means no shift.

If there are shift, observe whether N coordinate or E coordinate different. Normally, the E coordinates are the same, only the N shifted. Then you have to key in the combination to check. The first 5 digits shifts the N coordinates and the other 5 digits shift the E coordinates. You have to key in 1 combination, compare coordinates, if not ok, exit and restart again with a different. You have to write it down each time the different numbers and the effect on the coordinates.

Tips, the reg number is related to the memory card id. Initially my number is 0998000000. But when I copy into another memory card, it shifted and try again and got 0996000000 to work perfectly.

A lot of hard work, but believe me, once you got it, it will sure make your day."

FYI, my sweet number is 0798000000. I think torsten no is 0799000000. I am in Malaysia, Torsten is not. So I think location have no impact.

Tips:
Make sure you stay stationary at 1 location, and write down. Don't be lazy because you need to analyze the result to find out which number to change and to tembak more accurately.

Try not to do this at night for 2 reasons:
1) Dengue fever is on the rise and you are the sitting duck for mosquitoes.

2) At night is quiet. Your neighbours will be wondering what the heck are you doing after hearing "...Papago music...Searching for satellite...satellite search complete... " repeat and repeat for 15 minutes or more. (I did at night, mute sound .and close car door, sweating all over)

There are only S coordinates and E coordinates in my device, the first 5 digits shifted the S coordinates

I found the working code for my device -----> 0794000000

Thanks, u're the best

Anyway, there is a glitch when routing, during routing, my current position tends to dissappear for 1 seconds, then return to the normal the next second, is that a bug ?

Can I use the reg code for r6600 version of x7 in the same device ?





Thanks

manage to use the software but nothing happen when i click music video button, photo button works. tq

For those who are unable to download from filedude.
You can download from following link:
[Please Register or Login to download file]

panji19m wrote:For those who are unable to download from filedude.
You can download from following link:
[Please Register or Login to download file]

Thanks for sharing with us

Nagas wrote:Thanks for sharing with us

No problem,
Sound File
[Please Register or Login to download file]

Monters GPS wrote:[Please Register or Login to download file]

HI Moster,

Need happy file c2 b4800 as the link as above not exists anymore.

Thank you so much

Organic File:
[Please Register or Login to download file]

Hi Monters GPS,
Do you have the Original C1 9600 (No Exit Function)? This version can not do the Auto suspend when lost power.
I love that feature. No need to turn off my GPS when I turn off my car.

Rgds,
Panji

Guys...
I can't search using SLA Map. Anyone know why?