Hi, im using a Blaupunkt TravelPilot 100 and i can't start GPS signal. I copy the sw.unl in the Garmin directory of my SD and don't work, it says GPS only for Garmin Products. Even i try to configure port splitter without success. Can you help me. Sorry for my bad english.

lucas145 wrote:Hi, im using a Blaupunkt TravelPilot 100 and i can't start GPS signal. I copy the sw.unl in the Garmin directory of my SD and don't work, it says GPS only for Garmin Products. Even i try to configure port splitter without success. Can you help me. Sorry for my bad english.

Did you save the UNL as "all files" and not as ".txt?"

Yes i do it. I install other version of garmin and it runs :) OK !!! I've got signal of GPS.
I have 1 more questions, how can i set the que.exe in the start of wince 5?
Thanks for your time !!!

lucas145 wrote:Yes i do it. I install other version of garmin and it runs OK !!! I've got signal of GPS.
I have 1 more questions, how can i set the que.exe in the start of wince 5?
Thanks for your time !!!

Glad it's working well for you now. Sometimes it only takes a simple solution. Now what is this about the que.exe? You need to be more specific. Your goal was to have the program working [which it is now] so what more could there be?

I want to turn on the unit with the Garmin Xt program. Actually is with IGO. The garmin works excelent !!! :)

lucas145 wrote:I want to turn on the unit with the Garmin Xt program. Actually is with IGO. The garmin works excelent !!!

I'm a little bit confused here. Didn't you have to install an unlock in order to use iGO? The unlock takes over command of your device. So you have to go through the unlock in order to properly shutdown your device. This is why you probably have to go through iGO to make this happen. You may be able to modify it to shutdown through Garmin but since I don't have your device in front of me, this is something you should think out for yourself. Word of advice: BACKUP YOUR FILES/FOLDERS FIRST BEFORE MAKING ANY ATTEMPTS AT CHANGES!

chas521 wrote:I'm a little bit confused here. Didn't you have to install an unlock in order to use iGO? The unlock takes over command of your device. So you have to go through the unlock in order to properly shutdown your device. This is why you probably have to go through iGO to make this happen. You may be able to modify it to shutdown through Garmin but since I don't have your device in front of me, this is something you should think out for yourself. Word of advice: BACKUP YOUR FILES/FOLDERS FIRST BEFORE MAKING ANY ATTEMPTS AT CHANGES!

Thanks for the advice, i'll back up my files. I know i have to change the starup program in WinCe to boot from garmin application. The problem is that i don't know how do this, which files of WinCe have to change. Thanks for your time!

@lucas145

Honestly, my proficiency is with iGO. I only know so much about Garmin but there are people reading this who know the Garmin program much better than I do. I'm sure that one of them will read this and post.

Thanks of all your time and help. The maps of Igo in Argentina are no good. For this reason I change to Garmin. I'll hope someone else can help me. Grettings !

What do you mean when you say the Argentina map in iGO is no good?

chas521 wrote:What do you mean when you say the Argentina map in iGO is no good?

Yes, they are poor. The best maps in Argentina are for Gamin.

Hi
Me again with the same problem, MOTOROLA TN20, I unlocked it with miopocket, every GPS works well in it (IGO NDRIVE TOMTOM) but I could not make the garmin get the satellites. Tried everything, SW.UNL is fine, GARMIN loads, I indicate that it should work with COM7 but it keeps searching and searching for a satellite signal. maybe some tip for the .MSCR?
The best maps in Argentina are from an open community that works for GARMIN so we prefer to instal the GARMIN GPS.
Any idea? pls

Hi i. Install that version on witson china gps. Its run ok but can't load poi. I place the gdi files in all folders but garmin don 't found. Witson see the memory storagecard can we helpme

after the installation...my chinese pnd still ask for product key screen....y?

ripcurlz wrote:after the installation...my chinese pnd still ask for product key screen....y?

Install:
01. Choose "Yes" (Did this purchase of Garmin Mobile XT include a Garmin GPS receiver)
02. Choose "Done"
03. Choose "I Agree"
04. Go settings/about and get deviceID
05. Use Jetmouse and generate key and make SW.UNL file [color="sienna"]( put 25 digit unlock code first line and save as SW.UNL be sure there is not .txt extension )[/color]

I do not have device now, this is from my head and procedur is similar anyway