Run("Windows\undrv.exe", "UIO1: 1000 ""Drivers\BuiltIn\NDISUIO"" Drivers\BuiltIn\ipv6hlp Drivers\BuiltIn\ZeroConfig Drivers\BuiltIn\Ethman")

You are double quoting here, and also the run command in mortscript can only have one argument.

I got round this in one of my projects by writing a wince shortcut (.lnk) and running it.

Hi FBS can you point me to the project

It's not published anywhere, and I don't have access to the code right now, but check back later...

Hi FBS
any luck

This is a snippet from an unpublished project of mine (The one in my signature)

I needed to run an application to respond to a message silently and with different text depending on the request, that's three arguments, but mortscript's run command will only allow one argument at a time.

I got round this by writing a windows ce/mobile shortcut which allows several arguments, then running it.

Note: Sender and Text are pre-defined variables.

Code: Select all

WriteFile (SystemPath("ScriptPath")\"Temp.lnk", "72#""\Program Files\vijay555\VJSMSSender.exe"" "&Sender&" -silent "&Text)
Run (SystemPath("ScriptPath")\"Temp.lnk")

The resulting lnk text file looks like this...

72#"\Program Files\vijay555\VJSMSSender.exe" 07XXXXXXXX8 -silent Text to be sent goes here

If these shortcuts never change you only need to create them once (Possibly manually in notepad?) and just run them as normal.

Hi FBS
thanks fot the code but I dont quite understand what it does in relation to me trying to load 2 drivers one after another can you explain more ?

Stu

Start from the beginning, explain to me what you are doing and where you got the code from?

Hi FBS
First thanks for your time

I have a dynavin head unit thats been unlocked and a patch from petrut for wifi this works fine my dynavin head did not have TMC so I have spent the last month or so playing with a Royaltec TMC unit and a TTLto RS232 adapter to get primo to work with the TMC unit and now that works fine . However its one or the other I have been trying to load both drivers one after the other from boot with a time delay between so in other words with both devices pluged into a single usb slot the head detects unreconised usb loads the first driver then the head detects unreconised usb and loads second driver what would be nice would be to select second device with a button screen below is the origional code that loads the wifi driver if you insert the wifi dongle into the usb port

If(WndExists("Unidentified USB Device"))
WaitForActive ("Unidentified USB Device", 5)
SendKeys( "rt2870.dll" )
SendCR
Sleep(2000)
Run("Windows\undrv.exe", "UIO1: 1000 ""Drivers\BuiltIn\NDISUIO"" Drivers\BuiltIn\ipv6hlp Drivers\BuiltIn\ZeroConfig Drivers\BuiltIn\Ethman")
Else
Run("Windows\undrv.exe", "UIO1: 1000 ""Drivers\BuiltIn\NDISUIO"" Drivers\BuiltIn\ipv6hlp Drivers\BuiltIn\ZeroConfig Drivers\BuiltIn\Ethman")
Sleep(5000)
Run( "\StorageCard\Program Files\lockscreen\lockscreen.exe" )
EndIf
EndIf

so in short Im trying to hve both dongles installed but switch the second on when required if poss

hope this helps

Stu

Is this through a hub, and can you load both drivers at the same time?

If so it should be possible to do what you want?

Hi FBS

yes a hub thats the issue how to do this or better still select when to load second driver reason for this I need TMC all time but only require wifi every now and then

Stu

I don't know if a hub with two devices attached is supported under wince..?

Have you tried starting it all manually?

Hi FBS
yes if I put 1 device in with current set up it works fine if I then remove that usb device and install the other that works fine

forgot to add thats why I think if a time delay can be put between the drivers loading it should work

Well the sleep command is a simple delay command, or you could use a while command, I still don't know if wince supports a hub, if it's just a case of unplugging one device for another occasionally then I'd load the tmc driver at startup and set up a button to load the wifi driver, unless it can be automated.

Hi FBS
Thats it can you provide a code example for the button set up

Stu